How to Weld Thin Metal
Articles de soudage

How to Weld Thin Metal Without Burning Through

Nov 20, 2026

Table of Contents

If you’re learning how to weld thin metal, start with clean, tightly fitted pieces and a process that gives you a stable arc at low settings. For thin mild-steel sheet, short-circuit MIG with small-diameter solid wire is a practical starting point. Use brief welds spaced along the seam, and give each area time to cool before welding next to it. Test on scrap of the same thickness first. A setting that works on a flat test bead can still blow a hole through an open seam.

Choose a Welding Process for the Metal You Have

Measure the actual thickness near the joint before choosing a process. Thin-wall tubing, sheet metal, and a bracket cut from flat stock can look similar from the outside. Rust can also leave the edge you need to weld thinner than the rest of the part. Start with clean, uncoated mild steel if you’re practicing.

Process When to choose it What to check before welding
Short-circuit MIG Thin mild-steel brackets, covers, and other garage projects where you can shield the arc from drafts Check that your welder supports short-circuit MIG and the wire size you plan to use.
TIG Very thin or visible seams where precise puddle control matters Check that the machine can start and hold a stable arc at low current. Match the setup and filler to the metal.
Self-shielded flux-core Jobs where shielding gas is impractical and the wire is rated for the material thickness Check the wire’s minimum recommended thickness and follow its polarity requirements. Remove slag before welding over a previous deposit.
Stick Work within the electrode and machine’s usable range, with enough material to tolerate the arc Test on matching scrap. If the rod sticks at one setting and burns through at the next usable setting, switch processes for that joint.

For light-gauge mild steel, 0.023- or 0.024-inch solid MIG wire and a 75% argon/25% CO₂ shielding-gas mix are common starting choices. If your welder supports 0.023-inch wire, 0.023-inch ER70S-6 MIG wire is one option. Use the matching contact tip and drive-roll groove, and check the machine’s chart for the wire diameter and material thickness. Use a separate setup for stainless steel or aluminum. If you’re deciding between solid wire with shielding gas and self-shielded wire, see our flux-core vs. MIG welding comparison.

How to Weld Thin Metal Step by Step

Before striking an arc, put on a welding helmet, safety glasses, welding gloves, and flame-resistant clothing. Clear combustibles from the work area, including behind the part where sparks can travel. Use appropriate fume extraction and keep your head out of the plume. If you find galvanizing, paint, plating, or an unknown coating, identify it and arrange the appropriate exposure controls before welding.

Step 1: Clean and fit the joint

齐,夹具将钢板压平在工作台上。	Two thin steel sheets clamped flat on a welding table with their edges aligned for a butt joint.

Bring both mating edges to clean, sound metal. If you use an angle grinder to clean the weld area, avoid thinning the edges. For a butt joint, trim the pieces so the edges meet evenly, then clamp them flush. Fix gaps before welding. If the project allows a lap joint, the overlap gives you a supported edge to weld. Don’t change the joint design on a structural or safety-critical part.

Step 2: Set up a matching test joint

Use scrap of the same metal and thickness, and copy the joint type and welding position. For MIG, start with the manufacturer’s voltage and wire-feed settings for that combination. If you have an ARCCAPTAIN MIG200, use the MIG200 settings guide as a starting reference. Make a brief test weld, let it cool, and inspect it. Change one setting or technique at a time so you can tell what helped.

Step 3: Tack the pieces in place

Five spaced MIG tack welds along the butt joint between two thin steel sheets.

Space the tacks along the seam and alternate between separated spots. Pause to check that the edges are still flush and the gap hasn’t opened. If it has, stop and correct the fit while there are only a few tacks to deal with.

Step 4: Weld in short sections and move around the seam

Start in a cool area, make a short weld, then jump to a distant part of the joint. Keep the arc moving and give the previous area time to cool. If the joint requires a continuous seam, close the spaces in later passes. Where the back of a steel seam is accessible, clamp a clean copper backing bar against it to draw away heat.

Step 5: Check the weld before using the part

After it cools, look for pinholes, cracks, edges that have melted away, and spots where the bead sits on one piece without tying into the other. Check the back if you can. On a practice joint, a bend or peel test can help reveal poor fusion that a tidy-looking bead might hide. For load-bearing or safety-critical parts, follow the specified repair procedure and inspection requirements.

Diagnose Burn-Through Before Changing the Settings

Where the hole appears can tell you what to change. If it opens immediately at the same spot, inspect the joint there for a gap, a thin edge, or a place where the arc lands on only one sheet. If the first tacks hold but later ones open holes, the surrounding metal may be getting hotter with each tack. Give the area more time to cool and spread the next welds farther apart.

What you see What to try next
A hole opens where the edges separate. Refit the pieces. If the edge is too thin or damaged to meet cleanly, trim back to sound metal and fit a patch.
The first welds hold, but the seam starts to sag. Shorten each weld, move farther along the seam, and let the hot area cool before returning.
Burn-through happens at a thin-to-thick joint. On matching scrap, practice starting the puddle on the thicker piece and letting it briefly reach the thin edge.
The bead sits high and peels away on the test piece. Check for poor fusion. Return to the chart settings and adjust on scrap until the weld joins both pieces without opening a hole.

If you only have a stick welder, a small rod and the lowest dial setting may still leave you outside the usable range. If you try stick on matching scrap, follow the electrode maker’s current and polarity guidance. If you can’t get a stable arc that fuses both edges without melting them away, switch to short-circuit MIG or TIG.

Conclusion

To weld thin metal without burning through, fit the edges closely, choose a process that runs steadily at low output, and spread short welds along the joint so heat doesn’t build up in one spot. Before starting on your project, make a test joint from two offcuts of the same thickness. Use it to check that both edges fuse and that the sheet stays flat as you work along the seam.

Frequently Asked Questions

Why do welders drink milk before welding?

Some welders drink milk because of an old belief that it protects against metal fume fever. Milk does not protect your lungs from welding fumes. Control exposure with appropriate ventilation, local fume extraction, and respiratory protection where required.

What is the best welding method for thin metal?

Short-circuit MIG with small solid wire is a practical choice for many thin mild-steel projects. TIG is often preferable for very thin or visible seams where you need finer control of the puddle. The choice also depends on the alloy, joint fit, and how steadily your machine runs at low output.

Why am I burning through metal when welding?

Burn-through occurs when the arc melts through the full thickness of the metal. Common causes include staying in one spot too long, welding over an open gap, and adding another weld before the area has cooled. Check the fit and where the hole starts before lowering the machine settings.

What is the thinnest metal you can weld?

There’s no universal minimum thickness. As a reference, 24-gauge mild steel is about 0.024 inch (0.6 mm), and even a small gap can make a butt joint at that thickness difficult. Check your machine’s published range for the process you’re using and test the actual joint on matching scrap.

Can you repair a small burn-through hole in sheet metal?

Yes, a small hole in sound, nonstructural mild steel can often be repaired. Let the area cool, clean the edges, and use a copper backer if you can reach the back. Add brief tacks from sound metal around the edge. If the hole keeps growing or the surrounding steel is rust-thinned, cut back to sound metal and fit a patch.

Laissez un commentaire

Votre adresse email ne sera pas publiée.